Axial Compressive Properties of Prefabricated Circular Steel Tube Confined Concrete Columns
-
摘要:为了研究钢套管及套筒连接装配式圆钢管约束混凝土柱轴压性能，基于试验研究结果，对钢套管及套筒连接装配式圆钢管约束混凝土柱轴压性能进行了有限元分析. 首先通过有限元建立了现浇式和装配式圆钢管约束混凝土柱模型；然后从承载力-平均纵向应变关系曲线、钢管应力、钢筋应力和混凝土应力方面对比了现浇式与装配式柱的轴压性能；其次分析了装配式柱变形形态及受力机理；最后提出了装配式柱轴压承载力计算方法. 研究结果表明：与现浇式柱相比，装配式柱也具有良好的轴压性能和延性性能，钢管及钢套管对核心混凝土的约束作用更强，轴压承载力提高幅度为1.94%～6.17%；增加钢管厚度对提高装配式圆钢管约束混凝土柱轴压承载力最有效，提高幅度达59.15%，增加箍筋间距对其轴压承载力影响较小，减小幅度为2.91%；钢管纵向应力在靠近钢套管与钢管连接处较大，钢管环向应力在钢管通缝上、下附近区域较大，在钢套管装配处也较大；所提装配式柱轴压承载力公式计算值（ N uc）与有限元值（ N uf）、试验值（ N ut）的比值均值分别为0.964、1.014，方差分别为0.003 5、0.002 9.
-
关键词:
- 装配式圆钢管约束混凝土柱/
- 钢套管/
- 应力/
- 轴压承载力/
- 计算方法
Abstract:A finite element analysis based on test results was carried out to study axial compressive performances of the prefabricated circular steel tube confined concrete columns connected with steel sleeve and straight thread sleeve. First, finite element models of cast-in-situ and prefabricated circular steel tube confined concrete columns were established. Then, axial compressive performances of the cast-in-situ and prefabricated columns were compared in terms of the bearing capacity–average longitudinal strain curves, steel tube stress, rebar stress, and concrete stress; the deformation pattern and mechanism of prefabricated columns were analyzed. Finally, a calculation method of axial compressive capacity of prefabricated columns was proposed. Results show that the cast-in-situ columns and the prefabricated columns both have good mechanical and ductility properties; the steel tube and steel sleeve have strong confinement effect on the core concrete and the axial compressive bearing capacity was increased by 1.94%−6.17%. Increasing the thickness of steel tube can effectively improve the axial compressive bearing capacity by 59.15% at most, while increasing the stirrup spacing has little effect on the axial compressive bearing capacity, merely a reduction of 2.91%. The longitudinal stress of the steel tube is larger in the area near the connection between the steel tube and steel sleeve, while the circumferential stress of the steel tube is larger in the area near the upper and lower circular sutures of steel tube and is also larger at the assembly of steel sleeve. The average ratio of calculated value ( N uc) to finite element value ( N uf) and the average ratio of N ucto test value ( N ut) is 0.964 and 1.014, with variance of 0.003 5 and 0.002 9, respectively, where N uc, N ufand N utdenote respectively the values from formula calculation, finite element calculation, and test of the prefabricated column axial compressive bearing capacity. -
图 3有限元承载力-平均纵向应变关系曲线与试验对比
Figure 3.Comparison of bearing capacity-average longitudinal strain curves of finite element and test
图 4装配式与现浇式柱承载力-平均纵向应变关系曲线对比
Figure 4.Comparison of bearing capacity-average longitudinal strain curves of fabricated columns and cast-in-situ columns
图 5装配式与现浇式柱钢管纵向应力对比
Figure 5.Comparison of steel tube longitudinal stress of fabricated columns and cast-in-situ columns
图 6装配式与现浇式柱钢管环向应力对比
Figure 6.Comparison of steel tube circumferential stress of fabricated columns and cast-in-situ columns
图 7装配式与现浇式柱钢筋应力对比
Figure 7.Comparison of rebar stress of fabricated columns and cast-in-situ columns
图 8装配式与现浇式柱混凝土纵向应力对比
Figure 8.Comparison of concrete longitudinal stress of fabricated columns and cast-in-situ columns
图 9装配式柱破坏时典型的变形形态
Figure 9.Typical deformation pattern of fabricated columns during failure
图 10不同影响因素下装配式柱承载力变化曲线
Figure 10.Variation curves of bearing capacity of fabricated columns under different parameters
图 11装配式柱中钢管、钢套管和钢筋应力对比
Figure 11.Comparison of steel tube stress，steel sleeve stress and rebar stress of fabricated columns
图 12装配式柱稳定系数与长细比关系
Figure 12.Relationship between stability coefficient and slenderness ratio of fabricated columns
表 1试验试件参数及轴压承载力
Table 1.Parameters and axial compressive bearing capacity of test specimens
试件编号 试验试件尺寸
(D1、t1、L1)/mm钢套管尺寸
(D2、t2、L2)/mm套筒尺寸
(D3、t3、L3)/mm纵筋/mm 箍筋/mm λ 混凝土
强度等级轴压承载力/kN Nut Nuf Nuc S-FCTRC1 200、1.5、1 200 203、1.5、120 25、2.5、34 6 
20ϕ8@200 24 C50 2 746 2 904 2 801 S-FCTRC2 240、1.5、1 440 243、1.5、120 25、2.5、34 6 20ϕ8@200 24 C50 3 456 3 641 3 535 S-FCTRC3 200、1.5、2 000 203、1.5、120 25、2.5、34 6 20ϕ8@200 40 C50 2 633 2 718 2 552 S-FCTRC4 240、1.5、2 400 243、1.5、120 25、2.5、34 6 20ϕ8@200 40 C50 3 480 3 466 3 221 S-FCTRC5 210、3.0、630 216、3.0、120 19、2.5、34 4 
14ϕ8@200 12 C50 2 846 3 095 3 018 S-FCTRC6 210、3.0、630 216、3.0、120 19、2.5、34 4 14ϕ8@200 12 C80 3 785 4 090 4 121 CTRC-200-6-0A 200、1.5、1 200 200、0、120 25、0、34 6 20ϕ8@200 24 C50 2 667 2 820 CTRC-240-6-0A 240、1.5、1 440 240、0、120 25、0、34 6 20ϕ8@200 24 C50 3 366 3 546 CTRC-200-10-0A 200、1.5、2 000 200、0、120 25、0、34 6 20ϕ8@200 40 C50 2 480 2 560 CTRC-240-10-0A 240、1.5、2 400 240、0、120 25、0、34 6 20ϕ8@200 40 C50 3 414 3 400 c-210-3-50-a-235 210、3.0、630 210、0、120 19、0、34 4 14ϕ8@200 12 C50 2 780 3 023 c-210-3-80-a-235 210、3.0、630 210、0、120 19、0、34 4 14ϕ8@200 12 C80 3 710 4 008 
下载:
导出CSV
表 2有限元模型参数及轴压承载力
Table 2.Parameters and axial compressive bearing capacity of finite element models
有限元模型编号 有限元模型尺寸
(D1、t1、L1)/mm钢套管尺寸
(D2、t2、L2)/mm套筒尺寸
(D3、t3、L3)/mm纵筋/mm 箍筋/mm λ 混凝土强度等级 轴压承载力/kN Nuf Nuc FCTRC1 190、5、600 200、5、120 21、2.5、34 6 16ϕ8@70 12.6 C30 3 023 2 855 FCTRC2 190、5、600 200、5、120 21、2.5、34 6 16ϕ8@70 12.6 C50 4 065 3 592 FCTRC3 190、5、600 200、5、120 21、2.5、34 6 16ϕ8@70 12.6 C80 4 181 4 660 FCTRC4 190、5、600 200、5、120 15、2.5、34 6 10ϕ8@70 12.6 C30 2 827 2 626 FCTRC5 190、5、600 200、5、120 27、2.5、34 6 22ϕ8@70 12.6 C30 3 264 3 214 FCTRC6 190、5、600 200、5、120 21、2.5、34 6 16ϕ8@100 12.6 C30 2 935 2 855 FCTRC7 190、5、600 200、5、120 21、2.5、34 6 16ϕ8@160 12.6 C30 2 864 2 855 FCTRC8 190、5、1 200 200、5、120 21、2.5、34 6 16ϕ8@70 25.3 C30 2 632 2 738 FCTRC9 190、5、2 400 200、5、120 21、2.5、34 6 16ϕ8@70 50.5 C30 2 414 2 269 FCTRC10 184、2、600 194、5、120 21、2.5、34 6 16ϕ8@70 13.0 C30 2 060 1 991 FCTRC11 200、10、600 220、5、120 21、2.5、34 6 16ϕ8@70 12.0 C30 4 811 4 107 FCTRC12 190、5、600 194、2、120 21、2.5、34 6 16ϕ8@70 12.6 C30 2 751 2 855 FCTRC13 190、5、600 210、10、120 21、2.5、34 6 16ϕ8@70 12.6 C30 3 249 2 855 FCTRC14 180、0、600 190、5、120 21、2.5、34 6 16ϕ8@70 13.3 C30 1 426 1 313 FCTRC15 184、2、600 184、0、120 21、2.5、34 6 16ϕ8@70 13.0 C30 1 926 1 991 FCTRC16 180、0、600 184、0、120 21、2.5、34 6 16ϕ8@70 13.3 C30 1 361 1 251 下载:
导出CSV
-
MARTIN D, O ’SHEA M D, RUSSSELL Q, et al. Design of circular thin-walled concrete filled steel tubes[J]. Journal of Structural Engineering, 2000, 126(11): 1295-1303.doi:10.1061/(ASCE)0733-9445(2000)126:11(1295) MEI H, KIIOUSIS P D, EHSANI M R, et al. Confinement effects on high-strength concrete[J]. ACI Structural Journal, 2001, 98(4): 548-553. PETER M, JOHN F B, MOHAMED L. Composite response of high-strength concrete confined by circular steel tube[J]. ACI Structural Journal, 2004, 101(4): 466-474. AMIR F, FRANK S Q, SAMI R. Concrete-filled steel tubes subjected to axial compression and lateral cyclic loads[J]. Journal of Structural Engineering, 2004, 125(5): 631-640. 齐宏拓. 钢管约束混凝土轴压和偏压构件静力性能研究[D]. 哈尔滨: 哈尔滨工业大学, 2014. 周绪红,刘界鹏,张素梅. 圆钢管约束钢筋混凝土轴压短柱的轴压力学性能[J]. 工程力学,2009,26(11): 53-59.ZHOU Xuhong, LIU Jiepeng, ZHANG Sumei. Behavior of circular tube reinforced concrete stub columns under axial compression[J]. Engineering Mechanics, 2009, 26(11): 53-59. 经承贵,陈宗平,周山崴,等. 方钢管螺旋筋复合约束混凝土轴压短柱破坏机理试验研究[J]. 建筑结构学报,2018,39(3): 93-102.JING Chenggui, CHEN Zongping, ZHOU Shanwei, et al. Experimental study on failure mechanism of square steel tube and spiral reinforcement multiple confined concrete stub columns under axial compression[J]. Journal of Building Structures, 2018, 39(3): 93-102. 刘阳,郭子雄,吕英婷,等. 采用改进纵筋连接的足尺装配式钢筋混凝土柱抗震性能试验研究[J]. 建筑结构学报,2017,38(11): 101-110.LIU Yang, GUO Zixiong, LÜ Yingting, et al. Experimental study on seismic behavior of full-scale PRC columns with new mechanical splice technique for longitudinal reinforcement[J]. Journal of Building Structures, 2017, 38(11): 101-110. 李青宁,颜志勇,姜维山. 装配式钢板箍焊接栓筋连接框架柱试验研究[J]. 四川建筑科学研究,2013,39(4): 24-28.doi:10.3969/j.issn.1008-1933.2013.04.005LI Qingning, YANG Zhiyong, JIANG Weishan. Experimental study on seismic performance of assembly frame column with steel plate hoop-welding bolt reinforcement connection[J]. Sichuan Building Science, 2013, 39(4): 24-28.doi:10.3969/j.issn.1008-1933.2013.04.005 CHOI H K, CHOI Y C, CHOI C S. Development and testing of precast concrete beam-to-column connections[J]. Engineering Structures, 2013, 56(6): 1820-1835. 沈小璞,陈宏瑞,张红亚. 新型SRC框架-支撑结构体系抗震性能研究[J]. 合肥工业大学学报(自然科学版),2016,39(8): 1110-1116.doi:10.3969/j.issn.1003-5060.2016.08.021SHEN Xiaopu, CHEN Hongrui, ZHANG Hongya. Study of seismic performance of a new SRC frame-brace structure system[J]. Journal of Hefei University of Technology (Natural Science), 2016, 39(8): 1110-1116.doi:10.3969/j.issn.1003-5060.2016.08.021 李正良,徐姝亚,刘红军,等. 新型装配式钢管混凝土柱-钢筋混凝土梁框撑体系振动台试验研究[J]. 土木工程学报,2016,49(2): 22-30.LI Zhengliang, XU Shuya, LIU Hongjun, et al. Shake table test on a new type of precast CFST column-RC be-am braced frame structure[J]. China Civil Engineering Journal, 2016, 49(2): 22-30. 朱海清,李营,MAX S,等. 装配式钢管混凝土柱-盖梁节点抗震性能试验研究[J]. 土木工程学报,2017,50(8): 29-37.ZHU Haiqing, LI Ying, MAX S, et al. Exxpermental study on seismic behavior of assembly CFST column to cap beam connections[J]. China Civil Engineering Journal, 2017, 50(8): 29-37. MANDER J B, PRIESTLEY M J N, PARK R. Theoretical stress-strain model for confined concrete[J]. Journal of the Structural Engineering, 1988, 114(8): 1804-1823.doi:10.1061/(ASCE)0733-9445(1988)114:8(1804) -
下载:
20
14
点击查看大图
图(13)/
表(2)
计量
- 文章访问数:795
- HTML全文浏览量:353
- PDF下载量:15
- 被引次数:0